Autronic Telemetry System - NEW product!
Tune, view and log real time data with Autronic SMC, SM2 and Plug-and-Play
boards at line of site distances of 20 miles (US spec).
The Autronic calibration software can be used the same as if the normal PC Data
Cable was connected between the ECU and PC.
ECU's with chip versions 1.90 or higher are compatible with the Virtual Dash
software.
The modems are spread
spectrum and will frequency hop to maintain the connection. If the vehicle moves
out of line of sight, the modems will wait until it reappears and continue
transmitting the data.
Up to five slaves modems can be used with one master. (Example:- monitor up to 5
race cars on a race track - even more cost effective when used with multi-car
teams).
Kit
includes:
1 x Master Radio Modem
1 x Slave Radio Modem
1 x PC to Master Cable
1 x ECU to Slave Cable
1 x Master Base Antenna
1 x Slave Antenna
1 x Virtual Dash Software.
1 x Manual
Specifications.
Power
Supply.
The Autronic modems may be powered from either a 10 - 30 VDC or 10 - 24 VAC
supply Normal current drain 70mA (@12VDC) or 50mA (@24VDC)
· Current when transmitting 350mA (@ 12V), 250mA (@ 24V).
· Low power mode, normal current drain is 20mA (@ 12VDC), 15mA (@24VDC)
General
· Environmental -30 to 60 degC (full performance), -40 to 70 degC (typical
performance) 0 to 99 %RH
· EMC Compliant FCC Part 15 Class A
· Housing, extruded aluminium case 4.5" x 7.3" x 1.2" (114 x 185
x 30 mm), DIN rail mounting, removable terminal blocks for ease of
module replacement, terminals suitable for 12 gauge (2.5sqmm) conductors.
· LED indication for unit OK, radio TX and RX, serial TX and RX, DCD (comms
OK).
Serial
Port
· Standard data rates 1200 to 115200 baud. · RS232 and RS485 standard
interface connections provided, each connected to the same serial
port. Serial interfaces are asynchronous non-return-zero (NRZ)
format.
· The following characters are supported (selectable) - 7 data bits, even or
odd parity,1 start bit,1 or 2 stop bits; 7 data bits, no parity,1
start bit, 2 stop bits; 8 data bits, even or odd or no parity, 1 start bit,1
stop bit
· RS232 connection provides full duplex operation as a DCE device with RTS/CTS
hardware handshaking- standard D9 connector.
· RS485 connection provides half duplex operation for twisted-pair multidrop
networks.
· Terminal connectors provided for RS485.
Radio
Transceiver
· Frequency Hopping Spread Spectrum Transceiver
· Frequency USA/Canada 902 - 928 MHz, Australia 915 - 928 MHz, NZ 921 - 928MHz,
EU Countries 869MHz - 870MHz.
· Hop Sequence Length - 50
· Available Sequences - 16
· Transmit Power 1W · RSSI -60 to -120 dBm
· Signal Strength Indication -120 dBm to -80 dBm
· Expected line-of-sight range, depending on local conditions
· USA/Canada 20+ miles, Australia/NZ 20+ km, EU Countries 5+ km.
· RF Data Transmission Rate - 19200 baud, 57600 baud, 115200 baud
· Range may be extended by:- - up to five intermediate repeaters for controlled
mode - inlimited repeaters
for transparent mode
· Conforms to FCC Part 15 Class A and FCC Part 15.247
· Antenna connection is SMA coaxial
